Marantz RC2000MKII Bedienungshandbuch PDF herunterladen

LCD REMOTE CONTROLLER RC2000MKII

•The Marantz RC2000MKII remote control unit

is a “learning”-type, programmable unit capable of

controlling almost any component in your system, as well

as the Marantz D-BUS components (RC-5). The com-

ponents to be controlled can be selected with ten but-

tons.

OPERATION

The remote control unit (RC2000MKII) is a

system remote controller. The POWER button 5, 10-key

numeric buttons B and control buttons E are used in

common across different input source components.

The input source system controlled with the

RC2000MKII, such as receiver and AV amplifer changes

the input when one of the input selector buttons 9 is

pressed.

Example: To select the LD player as the input source for

receiver and play an LD on it

Press the LD button twice with in 2 seconds.

The input function of the receiver is switched

to LD and the RC2000MKII is set for control

of the LD player.

Press the PLAY button

to play an LD.

OFF

SOURCE

CLONE MACRO

MODE

MACRO

REMOTELEARNING

CONTROL

RC2000MKII

ON/OFF

VOL

OSD

GUIDE

MUTE

MACRO

POWER

LOW

USE

DVD

VCR

TUNER

TAPE

AUX

AMP

1 32

4 65

7 98

M C0

DSS

LOW

USE

LEARN

NAME

2 3 4

FUNCTION AND OPERATION

1 MODE (operating mode)

This button is used to change from normal operation to

the learning mode, and is used when “learning” com-

mands from other brands of A/V components. Each

time this button is pressed (using a small pointed in-

strument, such as the tip of a paper clip) the mode

changes as follows: LEARN → USE → NAME. As the

mode changes, the LCD display will show which mode

is currently selected.

2 MACRO (for multiple step macro functions)

This button is used to memorize a series of functions.

When this button is pressed, the RC2000MKII changes

to macro programming mode, and is ready to learn a

sequence of remote control commands.

1 2 3 4 5 6 ... 14 15

Inhaltsverzeichnis

Seite 1

1LCD REMOTE CONTROLLER RC2000MKII•The Marantz RC2000MKII remote control unit is a “learning”-type, programmable unit capable ofcontrolling almost any

Seite 2

10To “clone” (duplicate) the memory contents of one RC2000MKIIinto another RC2000MKII, please follow these steps:1. Place the source RC2000MKII (the o

Seite 3

11LAMP - Lighting function ON or OFF and TIMEPress the D-5 direct function button, and you can then set the time (inseconds) directly using the numeri

Seite 4

12TUNER 2 REC 3 PAUS pause4 STOP stop5 TP-2 commands for Tape 2 control(NO output)6 REC record7 PAUS pause8 STOP stop2 RDS 1 STM selects station mode

Seite 5 - RC2000MKII Basic Operation

13LD 3 REC 6 REC record7 PAUS pause8 STOP stop4 VCD 1 PBC selects play back control (for 2 KARA selects karaokeREST 3 IDX+ index up only) 4 IDX- index

14AUX 3 VCD/PHI 2 1 PBC selects play back control (for 2 KARA selects karaoke programREST 3 IND+ selects video index up only) 4 IND- selects video in

Seite 7

15Battery Installation and ReplacementInsert the 4 "AA" batteries, making sure to set them inwith the proper polarity.1.Press and pull.2.Loa

Seite 8

23 CLONEThe RC2000MKII has the ability to “replicate” itself,downloading all of its internal pre-programmed and user-programmed commands to another RC

Seite 9

3RC2000MKII keypad and DIRECT function commandswill be configured for DSS (digital satellite system) con-trol. We have included DSS commands within t

Seite 10 - Other Functions

4Liquid Crystal Display (LCD) WindowWithin this display, all operating messages (functionname, mode names, etc.) are shown. When a particularbutton i

Seite 11

5RC2000MKII Basic OperationUSE Mode:As supplied from the factory, the RC2000MKII is already permanentlyprogrammed with many pre-set commands common to

Seite 12

6LOWUSENAME12 3 45. Press and hold the corresponding SIDE-A button on the laser discplayer’s remote transmitter until the “OK” indicator appears in th

Seite 13

7Erasing the memory assigned to a DIRECT buttons:All codes and names which were previously memorized for each of thefunctions (such as TV, LD, VCR, et

Seite 14 - Top View

83. Press the command buttons in the desired sequence. When you pressa command button to be learned into the macro sequence, its namewill appear with

Seite 15 - LCD remote controller

9Using the macro function(s) you have programmed:1. Press the desired MACRO 6 button. The corresponding macronumber will appear at the bottom of the